Charlie's Angels (Gottlieb, 1978): Troubleshooting and System 1 Replacement Boards
Your Charlie's Angels by Gottlieb shows only a few lamps at startup, throws false stuck-switch errors, has fading displays, or no solenoids? These symptoms are typical of Gottlieb System 1 pinball machines whose original boards are now over 40 years old. The good news: our battery-free replacement boards, Plug & Play, bring your machine back to life.
Charlie's Angels (Gottlieb, 1978): Overview
Released in 1978, Charlie's Angels is a System 1 machine themed after the Charlie's Angels TV series and its trio of detectives, with alphanumeric displays. It uses the Gottlieb System 1 electronics.
- Manufacturer: Gottlieb
- Year: 1978
- Electronic system: Gottlieb System 1
- Type: solid state
- Theme: TV series Charlie's Angels
Common Issues (System 1)
The Gottlieb System 1 shares a well-known set of weaknesses regardless of the game:
- Leaking battery: the NiCad battery soldered to the MPU board corrodes traces and components over time. This is the #1 failure — remove it immediately.
- Poor grounds: the original ground wiring is undersized and causes resets and erratic behavior (ground mods are virtually mandatory).
- Corroded connectors: Molex connectors, especially the 46-pin MPU-to-driver connection, lose contact and require re-pinning.
- Power supply: unstable 5V (often the legs of transistor Q1 or the R4 trim pot), tired rectifier bridges, and overheating transformers cause crashes.
- Displays: digits that fade, flicker, or freeze at zero. Never connect or disconnect a display while powered on.
Charlie's Angels-Specific Issues (Forum Reports)
- Partial startup: only 3-4 playfield lamps light and nothing else, sometimes intermittent operation after about 5 seconds.
- False "stuck switch" errors at startup (drop 1, drop 2, slam, tilt, start): often caused by miswiring (a door mini-coil wrongly connected to a credit switch).
- Displays fade the more displays are connected (power supply problem). Never connect or disconnect a display while powered on — it burns out the display driver chips.
- Power: low 5V due to the legs of transistor Q1 (resolder them); a faulty R4 trim pot makes operation unstable.
- "No solenoids, only chimes": coils silent while chimes work — investigate on the driver and grounds side.
Compatible Replacement Boards for Charlie's Angels
Charlie's Angels runs on the Gottlieb System 1, a platform known for its fragility (leaking battery, weak grounds, corroded connectors). Pinballs Store offers battery-free replacement solutions:
- Gosof — replacement sound board.
For a dedicated System 1 CPU/driver board, contact us: we'll point you to the best solution for your Charlie's Angels. Plug & Play installation, battery-free, with free support.
FAQ — Charlie's Angels Gottlieb
I get false stuck-switch errors at startup.
Often miswiring (e.g. a door mini-coil connected to a credit switch). Check the wiring; a modern battery-free CPU stabilizes switch reading — contact us.
My displays fade as more digits light.
A power-supply problem — re-solder Q1's legs and check the R4 trim pot. Never connect or disconnect a display while powered on.
Do you have a replacement CPU board for my System 1?
Contact us — we'll point you to the best battery-free solution for your machine. The Gosof already covers the sound board.
Do I need to keep the original battery?
No. The NiCad battery is the #1 cause of corrosion on System 1 — remove it. Modern replacements are battery-free.
How long does installation take?
Our replacement boards are Plug & Play: just a few minutes, no soldering required, with tutorials and free support.
Does a battery-free board retain settings and high scores?
Yes. Modern replacement boards use NVRAM: no battery, no corrosion, and settings are preserved when powered off.
Step-by-Step Diagnostics
- With power off, visual inspection: look for battery leakage or corrosion on the MPU of your Charlie's Angels; remove the NiCad battery immediately if still present.
- Power supply: measure the 5V rail; if low, re-solder the legs of transistor Q1 and check the R4 trim pot.
- Grounds: apply the System 1 ground mods (ground wires to the CPU and driver boards).
- Connectors: re-pin the oxidized 46-pin MPU-to-driver Molex connector and the connectors under the battery.
- Displays: never connect or disconnect a display while powered on (it can destroy the display driver chips); test with a known good display.
- Final test: verify startup, credits, solenoids, and displays; if needed, contact free support.
Useful Guides
- How much does pinball machine repair cost? A price guide
- How much is my pinball machine worth? Value and estimation
- Pinball machine leg sizes: the complete guide
- Which board for a Gottlieb System 80, 80A or 80B?
See Also
- Roller Disco (Gottlieb, 1980)
- Torch (Gottlieb, 1980)
- Buck Rogers (Gottlieb, 1980)
- Totem (Gottlieb, 1979)
