Pinball Pool (Gottlieb, 1979): Troubleshooting and System 1 Replacement Boards
Your Pinball Pool by Gottlieb has several faulty displays, lock-ups after about 30 min, a corroded connector under the battery, or drop targets that won't reset? These symptoms are typical of Gottlieb System 1 pinball machines whose original boards are now over 40 years old. The good news: our battery-free replacement boards, Plug & Play, bring your machine back to life.
Pinball Pool (Gottlieb, 1979): Overview
Released in 1979, Pinball Pool is a System 1 machine with colorful seventies styling, drop targets, and alphanumeric displays. It uses the Gottlieb System 1 electronics.
- Manufacturer: Gottlieb
- Year: 1979
- Electronic system: Gottlieb System 1
- Type: solid state, drop targets
- Theme: American billiards / pool (8-ball)
Common Issues (System 1)
The Gottlieb System 1 shares a well-known set of weaknesses regardless of the game:
- Leaking battery: the NiCad battery soldered to the MPU board corrodes traces and components over time. This is the #1 failure — remove it immediately.
- Poor grounds: the original ground wiring is undersized and causes resets and erratic behavior (ground mods are virtually mandatory).
- Corroded connectors: Molex connectors, especially the 46-pin MPU-to-driver connection, lose contact and require re-pinning.
- Power supply: unstable 5V (often the legs of transistor Q1 or the R4 trim pot), tired rectifier bridges, and overheating transformers cause crashes.
- Displays: digits that fade, flicker, or freeze at zero. Never connect or disconnect a display while powered on.
Pinball Pool-Specific Issues (Forum Reports)
- Several faulty displays at once: suspect first the CPU connectors A1J2/A1J3, or the display-data circuits on the CPU board.
- Lock-up after about 30 min: displays go dark and the game freezes; unplugging then re-plugging the power-to-CPU cable restarts it temporarily (a connector needing re-work).
- Leaked battery under the MPU: corrosion attacks the connector located under the battery (switch inputs), causing random target lamps and unresponsive buttons.
- Low 5V after regulator repair: often a bad connection at transistor Q1's legs; re-solder the Base/Emitter eyelets.
- Drop targets that don't reset: at power-up, check the bank's coil, diode and transistor.
Compatible Replacement Boards for Pinball Pool
Pinball Pool runs on the Gottlieb System 1, a platform known for its fragility (leaking battery, weak grounds, corroded connectors). Pinballs Store offers battery-free replacement solutions:
- Gosof — replacement sound board.
For a dedicated System 1 CPU/driver board, contact us: we'll point you to the best solution for your Pinball Pool. Plug & Play installation, battery-free, with free support.
FAQ — Pinball Pool Gottlieb
My game locks up after about 30 minutes.
A connector (often the power-to-CPU cable) needs re-working — re-plugging it restarts the game temporarily. Re-pin it; a modern battery-free CPU improves stability.
My drop targets won't reset.
Check the bank's reset coil, diode, and transistor at power-up. Re-pin the connectors and apply ground mods.
Do you have a replacement CPU board for my System 1?
Contact us — we'll point you to the best battery-free solution for your machine. The Gosof already covers the sound board.
Do I need to keep the original battery?
No. The NiCad battery is the #1 cause of corrosion on System 1 — remove it. Modern replacements are battery-free.
How long does installation take?
Our replacement boards are Plug & Play: just a few minutes, no soldering required, with tutorials and free support.
Does a battery-free board retain settings and high scores?
Yes. Modern replacement boards use NVRAM: no battery, no corrosion, and settings are preserved when powered off.
Step-by-Step Diagnostics
- With power off, visual inspection: look for battery leakage or corrosion on the MPU of your Pinball Pool; remove the NiCad battery immediately if still present.
- Power supply: measure the 5V rail; if low, re-solder the legs of transistor Q1 and check the R4 trim pot.
- Grounds: apply the System 1 ground mods (ground wires to the CPU and driver boards).
- Connectors: re-pin the oxidized 46-pin MPU-to-driver Molex connector and the connectors under the battery.
- Displays: never connect or disconnect a display while powered on (it can destroy the display driver chips); test with a known good display.
- Final test: verify startup, credits, solenoids, and displays; if needed, contact free support.
Useful Guides
- How much does pinball machine repair cost? A price guide
- How much is my pinball machine worth? Value and estimation
- Pinball machine leg sizes: the complete guide
- Which board for a Gottlieb System 80, 80A or 80B?
See Also
- Count-Down (Gottlieb, 1979)
- Solar Ride (Gottlieb, 1979)
- Joker Poker (Gottlieb, 1978)
- Totem (Gottlieb, 1979)
