Torch (Gottlieb, 1980): Troubleshooting and System 1 Replacement Boards
Your Torch by Gottlieb has displays off and won't start, weak or dead coils, a fuse that blows repeatedly, or low 5V? These symptoms are typical of Gottlieb System 1 pinball machines whose original boards are now over 40 years old. The good news: our battery-free replacement boards, Plug & Play, bring your machine back to life.
Torch (Gottlieb, 1980): Overview
Released in 1980, Torch is a System 1 machine themed around fire and a flaming torch, with alphanumeric displays. It uses the Gottlieb System 1 electronics.
- Manufacturer: Gottlieb
- Year: 1980
- Electronic system: Gottlieb System 1
- Type: solid state
- Theme: fire / flaming torch
Common Issues (System 1)
The Gottlieb System 1 shares a well-known set of weaknesses regardless of the game:
- Leaking battery: the NiCad battery soldered to the MPU board corrodes traces and components over time. This is the #1 failure — remove it immediately.
- Poor grounds: the original ground wiring is undersized and causes resets and erratic behavior (ground mods are virtually mandatory).
- Corroded connectors: Molex connectors, especially the 46-pin MPU-to-driver connection, lose contact and require re-pinning.
- Power supply: unstable 5V (often the legs of transistor Q1 or the R4 trim pot), tired rectifier bridges, and overheating transformers cause crashes.
- Displays: digits that fade, flicker, or freeze at zero. Never connect or disconnect a display while powered on.
Torch-Specific Issues (Forum Reports)
- Displays off and game won't start: displays don't light, unable to register a credit or start a game; "glitchy" displays typical of System 1.
- No coils / weak coils: no coil responds, or only about 12V at the coils instead of full voltage.
- Fuse blows repeatedly: the display-control fuse (69V 1/4A slo-blo) blows every few minutes, sometimes after only a minute.
- Low 5V: often a bad connection at the legs of transistor Q1; resolder the feed-through eyelet.
- First steps: re-pin all connectors, check for battery damage and the power supply output.
Compatible Replacement Boards for Torch
Torch runs on the Gottlieb System 1, a platform known for its fragility (leaking battery, weak grounds, corroded connectors). Pinballs Store offers battery-free replacement solutions:
- Gosof — replacement sound board.
For a dedicated System 1 CPU/driver board, contact us: we'll point you to the best solution for your Torch. Plug & Play installation, battery-free, with free support.
FAQ — Torch Gottlieb
My display-control fuse (69V) keeps blowing.
A recurring System 1 fault. Check the display circuit and connectors before replacing again; a modern CPU/display setup avoids the stress — contact us.
My coils are weak (only about 12V).
Often low 5V from a bad Q1 connection, plus grounds. Re-solder Q1's eyelet, apply ground mods, and re-pin connectors.
Do you have a replacement CPU board for my System 1?
Contact us — we'll point you to the best battery-free solution for your machine. The Gosof already covers the sound board.
Do I need to keep the original battery?
No. The NiCad battery is the #1 cause of corrosion on System 1 — remove it. Modern replacements are battery-free.
How long does installation take?
Our replacement boards are Plug & Play: just a few minutes, no soldering required, with tutorials and free support.
Does a battery-free board retain settings and high scores?
Yes. Modern replacement boards use NVRAM: no battery, no corrosion, and settings are preserved when powered off.
Step-by-Step Diagnostics
- With power off, visual inspection: look for battery leakage or corrosion on the MPU of your Torch; remove the NiCad battery immediately if still present.
- Power supply: measure the 5V rail; if low, re-solder the legs of transistor Q1 and check the R4 trim pot.
- Grounds: apply the System 1 ground mods (ground wires to the CPU and driver boards).
- Connectors: re-pin the oxidized 46-pin MPU-to-driver Molex connector and the connectors under the battery.
- Displays: never connect or disconnect a display while powered on (it can destroy the display driver chips); test with a known good display.
- Final test: verify startup, credits, solenoids, and displays; if needed, contact free support.
Useful Guides
- How much does pinball machine repair cost? A price guide
- How much is my pinball machine worth? Value and estimation
- Pinball machine leg sizes: the complete guide
- Which board for a Gottlieb System 80, 80A or 80B?
See Also
- Roller Disco (Gottlieb, 1980)
- Buck Rogers (Gottlieb, 1980)
- Charlie's Angels (Gottlieb, 1978)
- Dragon (Gottlieb, 1978)
